Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Eddy currents in a copper plate in a time dependent 3D model

Please login with a confirmed email address before reporting spam

Hello,

I wish to calculate the eddy current loss in a circular copper plate. The eddy currents in the plate are generated due to time varying field in a copper coil above the plate.

The copper coil is excited with 1A/s from 0 to 100 s. So, the current in the coil changes from 0 to 100 A in 100 s. I have specified the external current density in the copper coil and the default magnetic insulation condition is applied at the outer air box.

When I run the simulation, the convergence plot is triangular. Additionally, NLfail increments continuously. Even after 5 hours, the progress is still less than 20 %.

Can you please let me know where I am going wrong? The mph file (v5.5) is attached herewith. Any help in this regard is highly appreciated.

Thanks a lot.

Warm Regards, Pranoti Raut



3 Replies Last Post Oct 8, 2021, 10:25 a.m. EDT
Robert Koslover Certified Consultant

Please login with a confirmed email address before reporting spam

Posted: 3 years ago Oct 6, 2021, 11:18 p.m. EDT
Updated: 3 years ago Oct 6, 2021, 11:23 p.m. EDT

Well, I think there are a number of separate issues with your model configuration, but in regard to your convergence issue, consider fixing the gauge. See screen image attached. This should at least make all your NLFails go away (although the simulation still begins rather badly). I think you should make some other changes too, but I'll let the real experts for these kinds of models provide those suggestions. Good luck.

-------------------
Scientific Applications & Research Associates (SARA) Inc.
www.comsol.com/partners-consultants/certified-consultants/sara
Well, I think there are a number of separate issues with your model configuration, but in regard to your convergence issue, consider fixing the gauge. See screen image attached. This should at least make all your NLFails go away (although the simulation still begins rather badly). I think you should make some other changes too, but I'll let the real experts for these kinds of models provide those suggestions. Good luck.


Please login with a confirmed email address before reporting spam

Posted: 3 years ago Oct 7, 2021, 7:21 a.m. EDT
Updated: 3 years ago Oct 8, 2021, 10:22 a.m. EDT

Dear Mr. Koslover,

I added the gauge fix as you suggested and it improved the convergence and computation time of my model. I also scaled the A variable manually by 0.001. This has solved my problem.

Thanks a lot for your time and suggestion.

Edit: I have a doubt regarding the current flow in the plate. The image is attached herewith. Shouldn't the current be going sideways along the length of the slit and resume its circular path?

Please state if there are any other discrepancies in the model.

Thank you.

Warm Regards,

Dear Mr. Koslover, I added the gauge fix as you suggested and it improved the convergence and computation time of my model. I also scaled the A variable manually by 0.001. This has solved my problem. Thanks a lot for your time and suggestion. Edit: I have a doubt regarding the current flow in the plate. The image is attached herewith. Shouldn't the current be going sideways along the length of the slit and resume its circular path? Please state if there are any other discrepancies in the model. Thank you. Warm Regards,


Please login with a confirmed email address before reporting spam

Posted: 3 years ago Oct 8, 2021, 10:25 a.m. EDT

Hello,

I have a doubt regarding the current flow in the plate. The image is attached herewith. Shouldn't the current be going sideways along the length of the slit and resume its circular path?

Please let me know if there are any other discrepancies in the model.

Thank you.

Warm Regards,

Hello, I have a doubt regarding the current flow in the plate. The image is attached herewith. Shouldn't the current be going sideways along the length of the slit and resume its circular path? Please let me know if there are any other discrepancies in the model. Thank you. Warm Regards,

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.