Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Specifying a rotating boundary condition

Please login with a confirmed email address before reporting spam

I would like to simulate a rotating wall condition.

For simplicity, imagine a square box. On the top surface of that box there is a circle. Inside of the box is a viscous fluid. I would like to impose a rotational velocity on said circle and observed the effect on the fluid inside the box.

I am defining the velocity as follows:

Ux = -(sqrt(x^2+y^2))*omega*sin(omega*t)*rect1(t[1/s])
Uy = (sqrt(x^2+y^2))*omega*cos(omega*t)*rect1(t[1/s])
Uz = 0

where omega is angular velocity.

I then apply this velocity to the circular boundary on top of the box.

I am trying to use a moving wall in my simulation but this does not seem to work. When I check my results there is no motion anywhere in the fluid or along the boundary.

Any thoughts on what I might be doing wrong?


12 Replies Last Post Jun 7, 2017, 2:06 a.m. EDT
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Jan 17, 2013, 3:37 p.m. EST
Hi

there must be something with your formula, have you tried to plot the velocity vector your get ? That often helps to check you got the cylindrical projection correctly set-up

On the other hand, you can define a local cylindrical coordinate system, and refer to the radius as sys2.r etc (it's sys2. or 3. or ... depending on how many coordinate systems you define)

--
Good luck
Ivar
Hi there must be something with your formula, have you tried to plot the velocity vector your get ? That often helps to check you got the cylindrical projection correctly set-up On the other hand, you can define a local cylindrical coordinate system, and refer to the radius as sys2.r etc (it's sys2. or 3. or ... depending on how many coordinate systems you define) -- Good luck Ivar

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Jan 17, 2013, 3:45 p.m. EST
I have two physics modules in my simulation; Heat Transfer (the circle imparts heat into the system) and Non-Isothermal flow (the fluid is non-Newtonian) and has a dynamic viscosity (I am using the carreau model). The only thing that I can see being updated from the nitf is kinematic viscosity. I am fairly certain that my velocity projection is accurate.

Does that shed any light on things?

I have two physics modules in my simulation; Heat Transfer (the circle imparts heat into the system) and Non-Isothermal flow (the fluid is non-Newtonian) and has a dynamic viscosity (I am using the carreau model). The only thing that I can see being updated from the nitf is kinematic viscosity. I am fairly certain that my velocity projection is accurate. Does that shed any light on things?

Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Jan 18, 2013, 1:50 a.m. EST
Hi

my only advice is : use the postprocessing to analyse your initial conditions (plot rotation vectors , different values and check how they look w.r.t. the expected results. Then do the same after solving (or after some solving) using the "plot while solving all solver steps" to check that it evolves in an understandable way

--
Good luck
Ivar
Hi my only advice is : use the postprocessing to analyse your initial conditions (plot rotation vectors , different values and check how they look w.r.t. the expected results. Then do the same after solving (or after some solving) using the "plot while solving all solver steps" to check that it evolves in an understandable way -- Good luck Ivar

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Jan 18, 2013, 2:25 a.m. EST
Hi,

Comsol will not find any motion unless you have inlet and outlet or you are using either FSI or rotating machinery interface or you are coupling equations of motion with boundary conditions via mathematics interface.

Cheers
Hi, Comsol will not find any motion unless you have inlet and outlet or you are using either FSI or rotating machinery interface or you are coupling equations of motion with boundary conditions via mathematics interface. Cheers

Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Jan 18, 2013, 2:46 a.m. EST
Hi

I would say, yes you can, with a sliding wall
my rectangle case is not converging to the default value, but the result is still OK, the concentric circle is OK

Files are 4.3a (if I manage to attach the files, ... now it works ;)

--
Good luck
Ivar
Hi I would say, yes you can, with a sliding wall my rectangle case is not converging to the default value, but the result is still OK, the concentric circle is OK Files are 4.3a (if I manage to attach the files, ... now it works ;) -- Good luck Ivar


Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Jan 18, 2013, 9:58 a.m. EST
Ivar,

Thank you so much for your help with this. Unfortunately, I am not able to open the files you posted.

I define the rotating boundary as specified. Everywhere else I have set as no-slip.

Are there any other boundary conditions required for the NITF? I am still not observing any rotation.

Thanks again.
Ivar, Thank you so much for your help with this. Unfortunately, I am not able to open the files you posted. I define the rotating boundary as specified. Everywhere else I have set as no-slip. Are there any other boundary conditions required for the NITF? I am still not observing any rotation. Thanks again.

Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Jan 18, 2013, 10:04 a.m. EST
Hi

here is a screen view, very simple set-up (oops have a Opera <-> Java update issue cannot upload from here anymore, checking with IE)

--
Good luck
Ivar
Hi here is a screen view, very simple set-up (oops have a Opera Java update issue cannot upload from here anymore, checking with IE) -- Good luck Ivar


Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Jan 18, 2013, 10:42 a.m. EST
Ivar,

I don't think I explained my problem well enough. I have included a simplified version of the model if you'd like to take a closer look.

Thanks again.

edit:

I got it to work.

Thanks for your help!
Ivar, I don't think I explained my problem well enough. I have included a simplified version of the model if you'd like to take a closer look. Thanks again. edit: I got it to work. Thanks for your help!


Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Jan 28, 2013, 2:55 p.m. EST
Hi

just had some minutes to take a closer look, My main question: why do you add HT and NITF as the latter contains all HT anyhow, no reason for doubling up, and now you need to equate the two T that represents the same dependent variable ?

And for the cylindrical coordinates, add a Definition cylindrical coordinate system, then you can refer to the components sys2.r etc, instead of the full equations, unfortunately COMSOL has not foreseen that you add your own coordinates system to define the mowing wall, sad, it would be so much easier ;)

And I would avoid the variable name omega, as it's used by COMSOL for frequency domain and other solvers, use rather some "omega_" or "my_omega"

I cannot get any arrow plot to show up, anyhow you must ensure that t>0.2 to avoid the rect is sending all velocities to =0

--
Good luck
Ivar
Hi just had some minutes to take a closer look, My main question: why do you add HT and NITF as the latter contains all HT anyhow, no reason for doubling up, and now you need to equate the two T that represents the same dependent variable ? And for the cylindrical coordinates, add a Definition cylindrical coordinate system, then you can refer to the components sys2.r etc, instead of the full equations, unfortunately COMSOL has not foreseen that you add your own coordinates system to define the mowing wall, sad, it would be so much easier ;) And I would avoid the variable name omega, as it's used by COMSOL for frequency domain and other solvers, use rather some "omega_" or "my_omega" I cannot get any arrow plot to show up, anyhow you must ensure that t>0.2 to avoid the rect is sending all velocities to =0 -- Good luck Ivar

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Jan 28, 2013, 3:03 p.m. EST
Thank you Ivar.

I have re-worked my model to use a 2-D axis symmetric geometry. It is working well now. Thanks for the help.
Thank you Ivar. I have re-worked my model to use a 2-D axis symmetric geometry. It is working well now. Thanks for the help.

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago May 24, 2014, 8:08 p.m. EDT
Dear All,

I am just wondering would it be possible to rotate a sphere (3d) at a specified angular velocity about a pre determined axis by providing BC on the surface of the sphere as done with the discs in the problem being discussed above. I am solving for a sphere rotating in a fluid filled channel.

Any help is greatly appreciated.

Thanks,
Seemit
Dear All, I am just wondering would it be possible to rotate a sphere (3d) at a specified angular velocity about a pre determined axis by providing BC on the surface of the sphere as done with the discs in the problem being discussed above. I am solving for a sphere rotating in a fluid filled channel. Any help is greatly appreciated. Thanks, Seemit

Please login with a confirmed email address before reporting spam

Posted: 7 years ago Jun 7, 2017, 2:06 a.m. EDT
In the original post:

===============
Ux = -(sqrt(x^2+y^2))*omega*sin(omega*t)*rect1(t[1/s])
Uy = (sqrt(x^2+y^2))*omega*cos(omega*t)*rect1(t[1/s])
===============

What is the "rect1(t[1/s])" term? The equations seem properly defined without that last term.
In the original post: =============== Ux = -(sqrt(x^2+y^2))*omega*sin(omega*t)*rect1(t[1/s]) Uy = (sqrt(x^2+y^2))*omega*cos(omega*t)*rect1(t[1/s]) =============== What is the "rect1(t[1/s])" term? The equations seem properly defined without that last term.

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.