Menu

Discussion Forum

New Discussion
Filter

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

modeling sessile droplet evaporation

Posted Jan 27, 2011, 7:18 a.m. EST 5 Replies

Maryam Dadkhah
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Dear Firends,

does any one has experience with modeling phase change from liquid to gas ? is there exists any tutorial ?

I intended to model evaporation of single droplet pinned of relatively hot serface .

I used general heat trasfer , incompresible navier stock and 2phase flow laminar phase field .


how could I check the conservation of mass and energy ?

I tried to run above problem with Moving Mesh ,ALE but I could not ,any suggestion ?

there is one toturial regarding 'Boiling water' I can not implement q (heat flux 1 & 2 ) in expresion ! I got error in expression and I can not run it , I assume t must be defined in other way but I have no idea how it should be define !

thank you in advance for your time and consideration

5 Replies Last Post Dec 3, 2012, 7:58 p.m. EST
Kalle Lofgren
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Jan 27, 2011, 8:47 a.m. EST
www.comsol.com/showroom/documentation/model/3972/
maybe this tutorial can help...
I am trying to get this to work in 4.0a at the moment...
good luck
http://www.comsol.com/showroom/documentation/model/3972/ maybe this tutorial can help... I am trying to get this to work in 4.0a at the moment... good luck
Ali Karimi
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Aug 18, 2012, 12:55 p.m. EDT
Hi Maryam,

Regarding to this post I also looking for someone who has experience in this case could you please share your good background based on this subject?
your immediate attention would be appreciated.


Best regards,
Ali
Hi Maryam, Regarding to this post I also looking for someone who has experience in this case could you please share your good background based on this subject? your immediate attention would be appreciated. Best regards, Ali
Khuram Saleem
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Nov 15, 2012, 6:24 p.m. EST

hello,

i m also working on phase change from liquid to gass ,
if any one has information regarding this topic plz help me out.


-which model is to be used?

-what are boundary conditions at inlet ?




Regards,

khuram saleem

hello, i m also working on phase change from liquid to gass , if any one has information regarding this topic plz help me out. -which model is to be used? -what are boundary conditions at inlet ? Regards, khuram saleem
SMHH
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Dec 3, 2012, 12:21 p.m. EST
Hi Maryam,

It seems that you want to do the same thing that these guys did before:

www.comsol.com/cd/direct/conf/conference2012papers/papers/13790/15249_marinaro_poster.pdf

I think that you can contact them directly and ask your questions.

I am also trying to model surface evaporation but it is difficult and there is no similar model unfortunately.


Cheers,
SMHH
Hi Maryam, It seems that you want to do the same thing that these guys did before: http://www.comsol.com/cd/direct/conf/conference2012papers/papers/13790/15249_marinaro_poster.pdf I think that you can contact them directly and ask your questions. I am also trying to model surface evaporation but it is difficult and there is no similar model unfortunately. Cheers, SMHH
Alexander Warning
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago Dec 3, 2012, 7:58 p.m. EST
look at the boiling water model they have. Same idea. It is very tough to fully implement

www.comsol.com/showroom/animations/3972/
look at the boiling water model they have. Same idea. It is very tough to fully implement http://www.comsol.com/showroom/animations/3972/

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content