Menu

Discussion Forum

New Discussion
Filter

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

How to establish Helix spring with wanted cross section and add some sub-sturctures on it?

Posted Jun 21, 2022, 7:39 a.m. EDT Geometry, Modeling Tools & Definitions Version 5.6 4 Replies

CJ H
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hello

I want to make a simulation with helix structures with specific cross section? How to do it?Could you give me some suggestions about it?

In addition, I also want to place some sub-structures on the pitch of helix. How to realize it?

Thanks

4 Replies Last Post Jun 22, 2022, 9:51 a.m. EDT
Jeff Hiller COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 3 years ago Jun 21, 2022, 9:25 a.m. EDT
Updated: 3 years ago Jun 21, 2022, 9:50 a.m. EDT

Hello CJ,

You can create a helix with arbitrary cross-section by first drawing the cross-section in a workplane and then sweeping that cross ection along a parametrized curve. You will find several discussions in this Discussion Forum where this has been discussed, including some example files provided by other users. Just search the Discussion Forum for "helix".

I don't quite understand your second question. It seems to also relate to geometry creation, so I would suggest browsing through Chapter 7 of the COMSOL Multiphysics Reference Manual, or viewing the video on geometry creation in the Learning Center

Best,

Jeff

-------------------
Jeff Hiller
Hello CJ, You can create a helix with arbitrary cross-section by first drawing the cross-section in a workplane and then sweeping that cross ection along a parametrized curve. You will find several discussions in this Discussion Forum where this has been discussed, including some example files provided by other users. Just search the Discussion Forum for "helix". I don't quite understand your second question. It seems to also relate to geometry creation, so I would suggest browsing through Chapter 7 of the COMSOL Multiphysics Reference Manual, or viewing the video on geometry creation in the [Learning Center](https://www.comsol.com/learning-center) Best, Jeff
CJ H
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 3 years ago Jun 21, 2022, 10:01 p.m. EDT
Updated: 3 years ago Jun 22, 2022, 9:32 a.m. EDT

Hello Jeff

Thank you for your timely reply.

In fact, I had try to draw a the cross-section in a workplane and then sweeping that cross ection along a parametrized curve. But I failed.

Thank you for your understanding.

Best wishes CJ

Hello Jeff Thank you for your timely reply. In fact, I had try to draw a the cross-section in a workplane and then sweeping that cross ection along a parametrized curve. But I failed. Thank you for your understanding. Best wishes CJ
Jeff Hiller COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 3 years ago Jun 22, 2022, 8:27 a.m. EDT
Updated: 3 years ago Jun 22, 2022, 10:05 a.m. EDT

If your license is eligible for technical support from COMSOL, and you would rather not share the model file on the Discussion Forum, please use the support portal to contact the support team. They'll able to help you.

Best regards,

Jeff

-------------------
Jeff Hiller
If your license is eligible for technical support from COMSOL, and you would rather not share the model file on the Discussion Forum, please use the support portal to contact the support team. They'll able to help you. Best regards, Jeff
CJ H
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 3 years ago Jun 22, 2022, 9:51 a.m. EDT

Hello，Jeff

I see, Also thank your advice,

Best

CJ

Hello，Jeff I see, Also thank your advice, Best CJ

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content